ECOS Paints - Interior EMR Shielding Paint

ECOS Paints - Interior EMR Shielding Paint

Was $9.95
$9.95
$9.95 – $339.90
  
  
 
ECOS Paints - Interior EMR Shielding Paint uses non toxic nickel to provide shielding against ELF, VLF, and EMR radiation. Having a dark grey color, it is intended to be over-painted by ECOS wall paint. Suitable for use on primed walls, floors and ceilings.

Just like all ECOS Paints products, theInterior EMR Shielding Paint is Zero VOC, simple to apply, contains no odor, and is HPD third party verified. It can be applied just like any traditional paint but is water based for easy clean up and can be applied in any space without discomfort.  

  • Zero VOC 
  • Easy to apply
  • Fast drying 
  • Safe for any area
  • No Glycol 
  • Zero VOC pigments 

Sizes/Dimensions

Comes in 2oz, Quart or Gallon Sizes

COLORS/OPTIONS

Ingredients/Composition

Technical Data

HPD Third Party Verified  
8260B VOCs (Liquid State GC/MS)

Safety Information

Photo Gallery

Installation

Application Coverage

Stir gently and thoroughly before use. Apply in two medium coats with a 6 - 9" foam or short pile gloss roller, ensure the first coat is fully dry before re-coating (minimum of 4hrs). Normally touch dry in 1-2 hours. Once the ELF shielding wallpaint is dry it can be finished by over-coating with any of our wall paints and, once earthed, the shielding paint is activated against both high and low frequency radiations. If protection is needed against high frequencies only (microwaves, mobile telephone masts, etc.) then grounding is not necessary. However, for full shielding efficiency, it is essential that this product be earthed (grounded). This can easily be achieved as follows: Turn OFF the power to all electrical circuits in the area. If in doubt about how to do this, consult a qualified electrician. Loosen the screws of all the light switch and power socket panels. When painting, extend the paint over the edge of the metal box behind the plate, as this should be grounded. If boxes are plastic, a grounding wire should be extended to the edge of the box and this used as the grounding point for the paint.

Application Notes

Typical Coverage: 550-600 sq ft. /gallon

Suggested Use

Benefits and Certifications

Care and Maintenance

Shipping Information

  • Sustain

  • Protect

  • Conserve

  • Reduce

  • Share

Sizes/Dimensions

Comes in 2oz, Quart or Gallon Sizes

COLORS/OPTIONS

Ingredients/Composition

Technical Data/h3>
HPD Third Party Verified  
8260B VOCs (Liquid State GC/MS)

Safety Information

Photo Gallery

Installation

Application Coverage

Stir gently and thoroughly before use. Apply in two medium coats with a 6 - 9" foam or short pile gloss roller, ensure the first coat is fully dry before re-coating (minimum of 4hrs). Normally touch dry in 1-2 hours. Once the ELF shielding wallpaint is dry it can be finished by over-coating with any of our wall paints and, once earthed, the shielding paint is activated against both high and low frequency radiations. If protection is needed against high frequencies only (microwaves, mobile telephone masts, etc.) then grounding is not necessary. However, for full shielding efficiency, it is essential that this product be earthed (grounded). This can easily be achieved as follows: Turn OFF the power to all electrical circuits in the area. If in doubt about how to do this, consult a qualified electrician. Loosen the screws of all the light switch and power socket panels. When painting, extend the paint over the edge of the metal box behind the plate, as this should be grounded. If boxes are plastic, a grounding wire should be extended to the edge of the box and this used as the grounding point for the paint.

Application Notes

Typical Coverage: 550-600 sq ft. /gallon

Suggested Use

Benefits and Certifications

Care and Maintenance

Shipping Information